SOMETHING NEW FOR HHO FUEL CELLS.
February 21, 2012
CONVERT DC INPUT VOLTAGE TO CONSTANT DC OUTPUT CURRENT WILL ALLOW CELL TO DRAW UP TO 32 AMPS,BUT ALLOW ONLY 12 AMP DRAW FROM CAR,AND REDUCES 12 VOLTS TO 3 TO 4 VOLTS AT CELL. TAKES VERY LITTLE KOH TO WORK 1/4 TSP.TO BE USED ON POS AND NEG SET UPS ONLY.
Video Rating: 5 / 5
Posted in 
Tags:
Nice, you gota check out my save money on fuel with one wire vid out.
powerstream sells it
@Hollywoods7 Nice job. Were you able to get the mod to the converter to allow it to get down to 2 volts?
@Hollywoods7 I don’t know for sure, but I would think that water would resonate at different frequencies based on temperature, impurities, and water level. If you had a microprocessor circuit like an Arduino, you could send a pulse every few seconds and listen for the ringing effect. Seek the maximum ringback and use that frequency. Just an idea.
@Hollywoods7 What is the make and model number for the converter please
I use 2.2v to 2.4v 40A out, 12v at 7A to 8A in bin doing it for over 2 years now.
I use SIL40C-12SADJ-VJ DC/DC Converters & Regulators 10.2-13.8Vin 40A
Hi Great video , Where is converter brought from? ANY LEADS WOULD BE GREAT
THANKS
10,000th view
Hey if I have a 32 plate pos neg setup will I run into any water vapor problems ?
@waterwart Well you know if somethig gets hot there are ways to cool it.I did not get there yet.
@Hollywoods7 what ever happen to tggas.
Hi there! :]
Im converting now my bmw 7 with same Converter…could you look at it in free time-meabye you find something I missed, please?
youtube.com/watch?v=Z5hCGC_I82A
Any Comment or Suggestion are welcome (part 1 is open for Comments).
Regards!
YOU CAN GET IT FROM POWER STREAM,YOU NEED TO REDUCE THE PLATE VOLTAGE DOWN TO 2 VOLTS ,INTEAD OF 3 AND 4 VOLTS FROM FACTORY.THAT WOULD BE A MOD TO THE CONVERTER.
Where can I buy it from?
@waterwart Also the new converter is a 120 v or 220 v converter I will let you know when I get it running.
@waterwart It is the 4 volts at the plate gap, which I already have a new converter from tggas which will have a lower and adj voltage for the gaps.
ya it’s great production…but is it getting hot?
what about maybe using a 12 volt d/c to a 120 volts a/c power inverter and then plug in a 120 volt computer power converter which has a 12 volt power out at a set amperage????
Hi. Would a 12 volt d/c to 120 a/c inverter work just as well and with a pwm to pulse the system????
@H2Truckers LET ME KNOW HOW IT WORKS OUT I AM TRYN A NEW CONVERTER THAT WILL ALLOW UP TO 630 WATTS NOT 130 LIMITED ON THE POWER STEAM………………..
I found this12v input DC-DC ATX power supply and it looks like it might work on a 5.5v for a cell setup like this -n+n-n+n-n+n- and so on at 20amps.
Good luck with yours.
@H2Truckers
You could, but it’s not.
When there is 32 amps going to the electrolyzer,that is not what is going through each cell. Remember, you have to hook this up to cells in parallel and that means the 32 amps is divided between the cells. So if you have a 4 cell system, there is only 8 amps going through each cell.
Here’s a good article about it.
tinyurl(.)com/2brvhgg
I use the same system, the convertor I bought last year. It saves me auto battery, and alternator upgrades.. I have the Drycell, but like my Stanley Meyer tube cells the best
@supercell9 I FOUND ,THAT I THINK THE PLATE VOLTAGE IS SET TO HIGH FOR THE CONVERTER,3.5 TO 4 VOLTS IS COOKING THE WATER. IT STARTS TO CREATE A CONDENSATION TRAIL AS SOON AS I START IT UP. MY CELL WOULD TAKE 1 HOUR TO START A TRAIL .I AM GOING TO TRY TTSGAS PWM IT IS ADJUSTABLE FROM 1.5 AND UP.
meant to say powering your cell